Jim Lawler's 1929 A Ford Bucket

This Bucket was bought as a rough tourer body which had been shortened, The rod was then built-up by Jim  and with help from Bill Jansen over a two year period. The car was registered
in 1968/69 and was used for a short time before being swapped for a 1939 Dodge coupe.

     This car has gone through a number of owners and is still registered to this day and resides          somewhere in Sydney NSW
     Specifications
Engine:                         1948 Ford 24 stud Side Valve V8
Transmission:           1939 Ford 3 speed manual
Differential:              1939 ford Diff
Front Suspension:        beam axle with transverse spring, split radius rods
Steering:                       VW Kombi steering box
Rear Suspension:        Transverse spring with split radius rods
Body:                         1929 Ford A tourer shortened
Chassis:                     A Ford chassis
Brakes:                      1939 Ford drum brakes front & rear
Wheels:                      Early Ford steel wheels
Other Modifications:
 
 

The car was purchased in 1997 at the 13th Nationals at Hawkesbury from Mr Rod Turnbull from Mount Riverview, in the Blue Mountains, NSW.  He informed me that he only owned the car for a period of some 12 months.  In this time he applied the paint job that you currently see today.

Following are a number of photos that were taken at the Hawkesbury Nationals in 1997.

During my early days of ownership my brother also found the attached clipping, however I’m not sure of the age of the advertisement.

Following is a list of the current specifications for the bucket that I have compiled over the last 4 years:

Owner : Chris and Debra Beuzeville
Club :  Street Rodders United
Make : Ford
Year :  1928

Body : channelled / shortened tourer body (built 1968-69)
Colour : Ford Toreador Magenta
Interior : black leather
Engine : 1951 Ford 24 stud sidevalve V8 (255 CID)
Transmission : 5 speed Toyota Celica
Diff :  1968-69 HK/HT Holden
Suspension :
 Front tube beam axle, transverse leaf spring, 4 bar set up and Holden spindles
 Rear transverse leaf spring, and 4 bar set up
Chassis : A Ford chassis
Steering : VW Kombi steering box (I would assume)
Brakes : 1968-69 HK/HT Holden, disk brakes front, and drum brakes rear
Wheels / Tyres :
 Front Kumho 185/65, 6” x 14” steel rims
 Rear Kumho 235/60, 8” x 15” steel rims

During my period of ownership the bucket has covered numerous kilometres including the following:
? In 1997, I picked up a longest distance travelled trophy for my trip from Sydney to Broken Hill, for the Highway ’32 Rod Run, (refer article in issue No. 117 of Australian Street Rodding.  This was one of my first big trips, and resulted in the handbrake busting, the radiator springing a leak whilst I was driving into the sun, just on dusk near Wilcannia, and two petrol tank mounts busting.
? For a period of 6 weeks at the beginning of 1998 the bucket was used as a daily driver in Sydney, as well as completing a Sydney to Bathurst, return trip each week.
? In 1999, the bucket almost completed a return trip to the 14th Nationals at Geelong, where I made it as far back as Young, just less than 200km from home.  This trip was quite an eventful trip, resulting in the complete destruction of one rear wheel bearing, the fuel pump packing it in, one of the petrol tank mounts busting, and a universal joint almost throwing in the towel.

The above includes a very abbreviated list of items that have required replacement in the last 4 years, but I finally feel that I am getting on top of what has resulted from years of neglect.

Following is a compilation of photos of the bucket, in its current form, that were taken on the grid at Mount Panorama, in Bathurst (the Buckets newest home)


Major aesthetic changes that have been carried out on the bucket during my ownership include the following items:
? Installation of a new radiator, chrome grille shell, and radiator support struts.
? A pair of 97 carbs and dual carb inlet manifold, new Mallory twin point distributor and spark plug leads, new stainless steel upper radiator pipes, new extractors and exhaust system, and a minor engine re-spray.
? A set of wind-wings, and corresponding rear vision mirrors.
? Installation of a Fibreglass ’32 dashboard and set of gauges, a complete rewire of the car, new brake, clutch, and accelerator pedals, and a new hand brake lever.
? Tidy-up of the rear cross member, with the addition of new petrol tank support brackets, and model A tail lights (fitted with blue dots).
? Numerous other minor modifications have been carried out in an attempt to tidy-up the car, and also out of necessity.
Future works to be carried out on the bucket will include:
? A complete re-spray, with a more nostalgic kind of paint job in mind.
? A panhard rod for the rear axle, as well as new rear shock absorber towers
? Installation of a HK/HT hydraulic clutch mechanism.
? Installation of a new floor pan.
? Minor rebuild of the current motor.

As a final note, as you may have already gathered, I am very much interested in the history of the bucket, any light that you may be able to shed on this matter would be greatly appreciated.
 
 
 
 
  1